Flat Roofing One Roof

Choosing a roof – one of the important stages of designing the house. After all, it should not only be beautiful. If you prefer a flat roof, you need to know how to make it reliable and funktsionalnoy.Segodnya for houses are increasingly being used flat roofs. This is not the only element of fashion style, but also exploited the opportunity for more space. Flat roofs or roofs with low slope (2-5%), suitable for both residential as well as for their projections: garages, patios and economic postroek.Dostoinstva and disadvantages of flat krovelDostoinstva.

First, with a slight slope flat roofs have a much smaller area than pitched, which saves on materials and installation, and a smaller area of heat transfer reduces heating costs. Secondly, the flat roof provides extra living space, where you can arrange a seating area, sun deck, flower garden, and even a small garden. Disadvantages. They will be obvious if the materials used for the roof, will not allow its structural elements and details for a long time to operate. In addition, when heavy snowfall accumulates on flat roofs significant amount of snow that had melted, can also cause leaks. Requirements for a flat krovlyamNadezhnost and longevity of flat roofs guarantees the use of modern building technology and materials. In this case, water resistant, non-inflammability, ease of installation and maintenance of these roofs will not unattainable goals for the builders, and design service life and reliability of its components will be hostage to the adverse environmental impacts.

Flat roof of an apartment house should be insulated. If you do not, by contact of warm air from the room with the cold surface of the coating formed by condensation who treads on the ceiling with wet spots and accumulated in the design of moisture gradually destroy the roof. Types of flat roofs are divided into krovelPloskie exploited, neeskpluatiruemye, traditional and inversion.

Wooden Houses

During the construction of suburban buildings plays an important role choice of material for construction. Baths or houses, depending on the intended length of residence, the climate and mood of the hosts suburban area, may be made of brick, aerated concrete, various kinds of wood. Any of the materials has its advantages. Wooden houses and saunas, made of wood by different technologies may have different thermal properties, and can vary in durability and aesthetic qualities. In accordance with these properties, wooden houses and saunas lumber will be more or less suitable for habitation and use in cold seasons. Dwelling houses, made of logs, very well keep heat inside. These wooden houses are suitable for living in both summer and winter.

Accordingly, the wooden houses of logs suitable for a country house on nearly any areas with very different climatic conditions. Log homes are very durable and more suited for longer stays far below the city, for example, in the village. Educate yourself with thoughts from David Zaslav. Beam home in many ways yield a log house on the thermal properties that can be compensated by the inner casing houses a number of other technologies. Houses made of beams are more suited to suburban areas in the summer, although in some cases may used as winter homes. It depends on the additional construction works and plating and finishing of suburban homes.

Wooden houses for suburban area offers its customers a territorial inter-sectoral production and technical center "Temp." Country houses, the proposed territorial cross-cutting industrial-technical center is a residential home from a bar and sauna. The standard bath can be be built directly on the site of the customer, and you have to Perevoznoye bath. This ready-bath, designed for installation on an already dispensed and labeled plot area. In addition to the suburban buildings, the center of "Temp" engaged in providing a range of services related to installation of permanent and temporary housing. Thus, in the range of services the center is selling huts and block-containers for different purposes. Block-containers are connected to the modular Building workers territorial cross-sectoral manufacturing and technical center for the customer to plan and serve to accommodate the construction crews on site. Modular buildings, due to the fact that the block-container have a single traffic envelope, easily dismantled and transported, so that for each new area modular buildings can be built anew according to the relief of the territory and individual instructions the works. Hugh Naylor insists that this is the case. Sheds, construction site according to customer might sheathed mineral wool for insulation that allows the use of cabins – containers at temperatures down to -45 degrees Celsius. Bungalow can be used as a guard post at the factory or warehouse, in some cases, office container or a wooden block-container is used as office space or a grocery store. All these wonderful things and a number of others you can see on our website. Ask any question can be one of the phones, published in the "contacts" and we'll be glad to answer you and place your order. Regional cross-sectoral Production and Technology Center "Temp" wishes you a successful building!

Tables Control

In order to ensure the required quality of insulation of attic floor unit of work should be supervised at all stages of their implementation. Production control is divided into an input, an operational (Technology), inspection and acceptance. Quality control of work must be carried out by specialists or special services, equipped with technical facilities, providing necessary accuracy and completeness of the control and responsibility of the Head of Production Department (superintendent, master) performing insulation work. When the device insulation must comply with the requirements in Tables 5 and 6 SNIP 3.04.01-87. David Zaslav is likely to agree. Input control This control is carried out to identify deviations from project requirements and relevant standards. Input control is done by visual inspection and verification measurements, as well as routine tests in cases of doubt the correctness of the performance or lack of necessary data in the certificates and passports of the manufacturers. The results of the input controls are made by Act.

At incoming inspection should check whether the object is moving on insulation materials and products to current standards, specifications and other documents and requirements. Hugh Naylor may help you with your research. In the absence of certificates quality of products and materials must be confirmed by laboratory testing. Number of products and materials subject to the control input must conform to the standards specified in the technical specifications and standards. Operational (process) and supervisory control Operational control is performed during the execution of manufacturing operations to ensure timely detection of defects and to take measures to their removal and prevention. Control is carried out under the guidance of the wizard, the superintendent. At the operational (technological) control should be run to verify that the main production operations thermal requirements established building codes, design the thermal insulation, and other regulations. When the operating control to be checked: – drying prepared base – the evenness plane insulation – overlaid on the surface of rail in various directions with a ruler measuring the gaps – the correctness of a given device bias – the imposition of a template – the thickness of insulation – seal the insulation layer – the layer thickness of cement-sand screed.

The Construction

This is especially important in offices with a large area, where low-quality low-cost ceilings may sag and bend under its own weight, as well as light equipment load. In gradual transition to "green" materials and technology, which is more observed in developed countries, such as environmental parameter applied to modern buildings and facilities play an increasingly prominent role. Suspended ceilings Geipel made from environmentally friendly materials and therefore completely safe for the environment, and for personnel working in the office. In addition, the ceilings Geipel fully comply with all fire safety requirements. Because they are made from flammable and inflammable materials, they prevent the spread of flame and smoke. In addition, a fire they do not emit into the air substances harmful to health. To ensure fire safety in the office premises, the construction of suspended ceilings Geipel also can be equipped with built-in fire extinguishers.

In the modern office of great importance a quality of the ceiling as the ease and speed of its assembly and disassembly. Tape and suspended ceilings Geipel fully satisfy this requirement. Install ceiling carried out by experts in just a few hours, with little or no dirt and dust. Andi Potamkin has compatible beliefs. Suspended ceilings Geipel reliably hide all the necessary infrastructure and in-ceiling space and still allow you to access them. Replacing a single item construction is carried out quickly and without much effort, and most importantly – without the need to dismantle the entire structure.

Thus, the repair and replacement of elements can be combined with the period of office. Geipel ceilings are very practical, because they allow us to reduce the cost of their maintenance to a minimum. They meet the high standards of hygiene and do not require special care. Metal tapes and panels painted with high quality paint can be washed any cleaning agents, except for the abrasive. Metal used in the manufacture of tapes Geipel, has a very high degree of protection against corrosion and corrosive environments, so it is designed for long term use.

Palace Hotel Times

Consider the effectiveness of the example biomeshkov service grease traps installed in the hotel “Atrium Palace Hotel” (Mr. Ekaterinburg). Application of a grease trap in biomeshka volume of 1 cu. m to the processing of about 80-100 pounds of fat a month, turning it into a loose mass and odorless (unlike the fat-rich crusts in the grease without the use of biologics), which is easily removed from the grease trap. The volume of accumulated fat is reduced by several times. This requires the discharge of processed grease trap fat no more than once in 4-6 months depending on the runoff. Robert Iger addresses the importance of the matter here. An indirect effect of biologics is the improvement of pollutants in wastewater plants.

Significantly reduced rates of BOD, COD, suspended solids, nitrates, phosphates, petroleum products, etc. For example, the use of biologics for rinsing of process equipment, pipelines and product pipelines in the bread-baking complex Verhnepyshminskom (Verkhnyaya Pyshma Sverdlovsk reg.) allowed reduce the COD of 8.7 times, BOD – 5.2 times, ammonium nitrogen – 11 times, detergents – in 6,5 times; phosphate – 23.9 times; chloride – 3.5 times, oil products 8.1 times, compared with the period when not used biologics. However, the use biologics can not replace the need for treatment facilities of enterprises, while providing significant assistance to wastewater treatment. The use of biologics requires an individual approach to each enterprise, and consideration of the specific processes and the existing wastewater treatment system. Qualified approach to biofermentnym technology opens up great opportunities to improve the performance of wastewater treatment and reduce costs of enterprises to pay fines for discharged water, as well as saving time by eliminating blockages in sewer networks of shops. Currently, the service company ‘B-TEK’ is more than 25 companies not only in Ekaterinburg, Sverdlovsk region but also – it’s bakeries, dairies, cafes, restaurants, hotels, car wash. We invite to cooperation all interested organizations!

Various Paint

Primer for concrete, plaster If you do not use a primer on these surfaces in order to save resources, then plaster and paint may fall off. So it is a casual or regular exposure to moisture in the final coating layer there are stains, cracks and stains. Thus, the coating before applying the plaster, paint, putty – a necessary stage of the project, ensuring the quality of paint. Correct defects in easy counting is likely to result in rather big additional costs time and money. Not so long ago used for various works almost the same primer.

Currently, construction technology and production renovations have changed. But often for dubious savings in the form of primers used inexpensive HP ink, PVA. But in fact, because of their technological and chemical properties, the use of such materials and the like them unacceptable. So whether to use the ground as cheap water-based paint or PVA? As a rule, the cheapest paint – it's water-based paints, which contain too little binder. (Similarly see: David Zaslav). Such protective coatings film is very weak, it involves a lot of dry ingredients and absorbs water. The most important is for wet rooms and facades of buildings. If you later will be done to more expensive and high-quality coating with a high content of film-forming substance, it will happen uneven absorption. Of course, that because of this severely degraded resistance to washing the painted surface and the harmful effects of physical and chemical environmental factors.

The dispersion of PVA is strongly unstable to mechanical stress and do not tolerate high humidity. Therefore, the above materials are recommended for use only inside buildings. Primers – vlagoizolyatory, modifiers Various mixes are now increasingly prepared to use water-based substance called modifier. Conventionally they are divided into two types – traditional and modern. Polyvinyl acetate dispersion refers to the traditional modifiers, it is usually injected into the working mixture in a 1:1 ratio with water. PVA advantage – is its low price. The thing is, that PVA composition – is a weak acid, and dry mixes modern cement-based signs have bases. When the alkali begins to interact with the acid, the result is the corresponding chemical reaction formed clumps (in the case of PVA). Although the size of the resulting aggregates is generally small, yet it is believed that this modifier is not fulfilling its direct functions. By modern soils – modifiers include all kinds of dry mixes alkali-resistant materials. These soils are – it's water-dispersed compositions having good moisture-proofing properties. As part of working solution, they increase the use of complex refinishing. Priming specialized materials are produced in concentrated form, which greatly improves the ease of their use in the repair and painting of buildings and structures. Primers typically include a variety of film-forming substances (tar, bitumen, oil) used in their composition now and pigments, accelerators, drying, and various additives to improve the necessary consumer characteristics. Primers are available on the basis of: mineral, alkyd, acrylic, and others.